Welcome to WetTrades!
(03) 9555 4108 info@wettrades.com
  • $160.00

    Crommelin Enhance Penetrating Clear 15L

    Crommelin Enhance Penetrating Clear 15L

    Enhance Penetrating is a highly water repellent treatment that penetrates deep into surfaces to cure and impede the passage of moisture. Enhance Penetrating reacts with soluble salts in cementitious surfaces to block capillaries whilst still allowing the substrate to release retained moisture, i.e. breathe.

     

    Features

    • Penetrating treatment

    • Allows area treated to “breathe”

    • “Invisible” protection

    • Does not increase slipperiness of surface

    • Enhances life of pavers and serviceability

    • Suppresses efflorescence (white salts)

    • Reduces spalling by minimising water penetration

     

    Areas of Use

    • Clay brick

    • Concrete pavers

    • Stencilled concrete

    • Concrete and concrete block

    • In-situ concrete and reconstituted stone paving

    • Natural stone

    • Exposed aggregate panels

    • Reconstituted limestone

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable applicators so if you are looking for the right coatings specialist we can connect you without delay.

    This product is part of our large selection of Waterproofing and sealing supplies and you can find more information and data sheets on this product by following the links to the Crommelin website.

    Crommelin Enhance Penetrating Sealer

     

    Data Sheet Crommelin Enhance Penetrating Sealer

  • $170.00

    Crommelin Membryl 15L Grey/White

    Crommelin Membryl® 15L

    Membryl® is a waterborne elastomeric waterproofing membrane with outstanding long-term UV stability. Membryl® is an effective anti-carbonation membrane for concrete as it exceeds the “Klopfer Criterion” requirements of Sd < 4m and R > 50m.

     

    Features

    • Seamless waterproofing system – liquid applied with no joints or laps, not allowing ingress of water or contaminants

    • Elastomeric, even after weathering 

    • Anti-carbonation protection of concrete 

    • Tough – high tensile strength and hardness 

    • Allows substrate to breathe 

    • Fungal and algal resistive – an extended life and clean appearance in high humidity environments 

    • Fire and flame resistive 

    • Chemical attack resistive 

    • Decorative – available in a wide range of durable colours 

    • Excellent resistance to dirt pick up 

    • Very high adhesive strength – no primer required on most surfaces

    • High build – bridges fine cracks 

    • Resistive to impact and light traffic damage 

    • Weatherproof and lightfast 

    • Reflective properties aid in reducing internal air temperatures by up to 20 degrees C

    • Aids in reduction of CO2 emissions 

    • Energy and cost efficient 

    • Resistant to chemical attack 

    • Very high adhesive strength – no primer required on most surfaces 

    • Weatherproof and lightfast 

    • Fungal and algal resistant in high humidity environments 

    • Excellent dirt pick up resistance 

    • Tough – high tensile strength and hardness Low VOC

     

    Areas of Use

    • Concrete structures

    • Concrete roof areas

    • Internal walls

    • External walls – concrete, concrete block, brick and other masonry surfaces.

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable applicators so if you are looking for the right coating specialist for your job we can connect you without delay.

     

    This product is part of our large selection of Waterproofing & Sealing supplies and you can find more information and data sheets on this product by following the links to the Crommelin website.

     

    Crommelin Membryl

     

    Data Sheet Crommelin Membryl

  • $10.00

    Mac Medium Render 20kg

    MACRENDER Medium Render 20kg

    Medium grade cementitious render for application to stable and porous masonry surfaces.

     

    KEY FEATURES

    • Just add water

    • Factory blended for optimum consistency

    • Excellent durability 

    • Improved wokability and application properties

    • Will not go drummy like traditional sand and cement renders

     

    SUITABLE APPLICATIONS

    • Stable and porous masonry surfaces 

     

    COMPOSITION

    • Type HE off white portland cement

    • Graded silica sands

    • Redispersible polymer powders

    • Workability additives

    • Water retention agents for improved hydration

     

    COVERAGE

    • Approximately 3-5 square metres per 20 kg bag

     

    CLEAN UP

    • Water

     

    PACKAGING

    • 20 kg paper sacks

    • 60 x 20 kg sacks per pallet lot

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Renderer’s so if you are looking for the right tradesman for your job we can connect you without delay.

    This product is part of our large selection of Render materials and you can find more information and data sheets on this product by following the links to the Mac Render website.

     

    Mac Render Medium Render

    Tech Data Mac Render Medium Render

    MSDS Mac Render Medium Render

     

  • $65.00

    Builders Film 1/2M 100um 100M Black

    Builders Film 1/2M 100M 100um Black Multi-Purpose

    Builder’s Multi-Purpose Film is a high quality, black polythene film that can be used in a variety of ways.

    Available in a conveniently sized roll, Grunt Builder’s Multi-Purpose Film is ideal for use as a plastic tarpaulin, temporary weather protection during building, moisture barrier under concrete slabs or as a drop sheet.

    • Temporary weather protection during building

    • Moisture barrier under concrete slabs

    • Plastic tarpaulin

    • Drop sheet

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Tradies so if you are looking for the right man for your job we can connect you without delay.

     

     

  • $10.45

    Unitex Redi Render 20kg

    Unitex Uni-Dry Cote Redi Render 20Kg

    Designed for application over clean brickwork and blockwork. It is available in both fine (Harbour Fine) and medium grades. Generally for skim coat work, it is applied in 2 passes – a build coat and then a final sponge finish. Coverage is 3-4.5 m2 per bag

     

    Size: 20kg bags

    Coverage: 3.5-4.5m2

    Suitable for: New & / or Old Brick, Cement Block

    Apply with: Spray or Trowel

    Safe Use: Refer to the MSDS 

    Unitex® Uni-Dry Cote® Redi Render™ is trowel-applied and suitable for a one-coat or two-coat application on all suitable masonry surfaces, eg Brick or Block etc, both inside and out, and is recommended to aid in the protection of masonry walls from the damaging effect of surface ingress of moisture. If the surface is in good order only a skim coat is required.

    Unitex® Uni-Dry Cote® Redi Render is a cement based polymer modified, High Performance Water Resistant and adhesion promoted masonry render system. Unitex Uni-Dry Cote® Redi Render is applied direct to sound and prepared masonry surfaces, either mechanically (sprayed) or by Trowel and rubbed up to a true and even surface with a float. This product is workable at thicknesses up to approximately 4 mm.

    Unitex® Uni-Dry Cote® Redi Render enhances the appearance of masonry surfaces and may be sponge-finished for a concrete old world sandy surface effect or usually merely overcoated with any of the range of Unitex Roll, Trowel or Brush Applied Texture coating systems.

    Unitex® Uni-Dry Cote® Redi Render is supplied in ready-to-use 20kg bags.

    Approximate coverage per bag is 3.5-4.5m².

     

    Condition of Substrate

    Before application of any render the surface of the substrate must be clean, dry and free of any debris. This means that any loose or damaged substrate must be removed, or patched and made good, prior to application of the base render.

    The substrate surface must be cleaned free of any grease, oils, scaling laitance, efflorescence, form-oil compounds, mould, fungi, rust, dirt, dust or any other foreign matter. Pre-painted surfaces must be wire-brushed back to the bare substrate.

    It is the responsibility of the Builder or Head Contractor to make good any substrate before the render is applied. Contact Unitex for advice or site visit by our representatives.

    Adequate expansion joints are required to minimise cracking on the surface of the render. Location of the expansion joints is also the responsibility of the Builder or Head Contractor. Unitex® recommends expansion joints to every elevation and between different substrates, to allow for building movements and or stresses.

    If such expansion joints are not provided by the Builder or Head Contractor, cracking due to movement of the substrate may occur. This is in no way indicative of faulty material. Rather it indicates sub-standard building practice.

     

    Adding Water

    Unitex® Uni-Dry Cote® Redi Render products are dry powder-based products. This means that you are getting a 100% active product. All that is required is for clean water to be mixed in, on site, immediately prior to application to the substrate.

    The recommended starting point is to add approx. 25% by volume, (based on the amount of powder render to be used), of water into a clean container (approx 4.5 litres per bag). Then slowly add the powder, with drill mixing, until the desired slump (consistency) is achieved.

    Unitex® Uni-Dry Cote® Redi Render should be left a minimum 72 hours after application and wait until fully cured before overcoating with a texture from the Unitex Applied Finishes range.

     

    Unitex Uni-Dry Cote® Redi Render™:

    • Trowels on easily, smoothly and thinly

    • Is polymer-modified for strong adhesion to surface

    • Is more waterproof than conventional render

    • Just Add Water  – less margin for errors

    • Is ideal for renovation works or over new surfaces

    • Consistent quality

     

    Guide to Good Mixing Consistency

    1. Add the contents of the bag slowly to 4 litres of water (25% volume of entire bag) with vigorous drill mixing to ensure a lump free render of required slump.

    2. The mix can be later water thinned to required viscosity.

    3. Ensure wall surface is stable, clean, dry and free of dust, etc prior to application.

    4. For difficult masonry and non-masonry surfaces contact Unitex for product and surface preparation advice.

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Renderer’s so if you are looking for the right tradesman for your job we can connect you without delay.

     

    This product is part of our large selection of Render materials and you can find more information and data sheets on this product by following the links to the Unitex website.

     

    Unitex Redi Render 

    MSDS Unitex Redi Render

  • $18.00

    Mac HBS Render 20kg

    MACRENDER HBS Render 20kg

    High bond strength, medium grade cementitious render for application to low porosity surfaces.

     

    KEY FEATURES

    • High polymer modification for excellent bond strength

    • Just add water

    • Factory blended for optimum consistencyExcellent durability 

    • Improved wokability and application properties

    • Will not go drummy like traditional sand and cement renders

     

    SUITABLE APPLICATIONS

    • Painted masonry based surfaces

    • Expanded polystyrene (EPS) base sheet

    • Rigid thermoset phenolic EIFS systems eg. Kooltherm or Masterwall K-Series

    • See Render Selector for details

     

    COMPOSITION

    • Type HE off white portland cement

    • Graded silica sands

    • Redispersible polymer powders

    • Workability additives

    • Water retention agents for improved hydration

     

    COVERAGE

    • Approximately 3-5 square metres per 20 kg bag

     

    CLEAN UP

    • Clean tools immediately following use as hardened material will prove difficult to remove

     

    PACKAGING

    • 20 kg paper sacks

    • 60 x 20 kg sacks per pallet lot

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Renderer’s so if you are looking for the right tradesman for your job we can connect you without delay.

    This product is part of our large selection of Render materials and you can find more information and data sheets on this product by following the links to the Mac Render website.

     

    Mac Render HBS Render

    Tech Data Mac Render HBS Render

    MSDS Mac Render HBS Render

     

     

  • $9.00

    Soudal Sealant 600ml Concrete Grey

    Soudal Multibond SMX35 Seal & Stretch Concrete Grey 300ml

     

    DESCRIPTION

    Multibond SMX35 is a high quality, single component, permanently flexible joint sealant. Perfect for internal & external applications. Based on SMX® Polymer Multibond SMX35 has a “Shore A” hardness of 35 and can accommodate movement of ± 20 %. Multibond SMX35 has excellent UV resistance, elasticity and can be sanded and painted with most types of paint. Once cured forms a strong, flexible, waterproof seal and bonds to the widest range of substrates. Multibond SMX35 can be used for damp and wet surfaces.

     

    APPLICATIONS

    Multibond SMX35 – Seal & Stretch is ideal for a wide range of sealing applications in construction and industrial including…..

    • Expansion joints

    • Joints under waterproofing membranes (water-based, solvent-based and acrylic)

    • Masonry and precast concrete joints

    • For sanitary, bathroom and kitchen areas (resists mould growth)

    • For walls and perimeter joints

    • For water retaining structures (Concrete Grey water potable approved)

    • For lap joints in roofing, guttering and cladding,

    • For air conditioning ducting,

    • For caravan, bus and automotive use

    • For window and door frames.

     

    FEATURES & BENEFITS

    • Elastic sealant

    • Highly flexible ±20%

    • Internal & external

    • Multipurpose

    • UV Resistant

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable applicators so if you are looking for the right coatings specialist we can connect you without delay.

    This product is part of our large selection of sealant and adhesive supplies and you can find more information and data sheets on this product by following the links to the Crommelin website.

     

     

    Soudal Sealant

    Tech Data Soudal Sealant

    MSDS Soudal Sealant

     

  • $52.00

    Mac Render 1140 Medium Texture 15L

    Mac Render 1140 SANDFINISH Medium Texture 15L

    Medium grade acrylic based architectural finish formulated for trowel application.

     

    KEY FEATURES

    • Excellent durability

    • Tintable to almost any colour

     

    COLOUR RANGE

    • Most non metallic colours, pastel, through deep base.

    • Some ultra deep/bright colours may not be possible.

    • Some colours may not be suitable for exterior use.

     

    COMPOSITION

    • Premium acrylic copolymer

    • Marble aggregates

    • Mould & fungus inhibitors

    • Premium pigments & fillers

     

    COVERAGE

    • Approximately 10-12 square metres / 15 litre pail

     

    CLEAN UP

    • Water

     

    PACKAGING

    • 15 Litre plastic pails

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable renderer so if you are looking for the right tradesman for your job we can connect you without delay.

     

    This product is part of our large selection of Render materials and you can find more information and data sheets on this product by following the links to the Mac Render website.

     

    Mac Render 1140 Medium Texture

     

    Tech Data Mac Render 1140 Medium Texture

     

    MSDS Mac Render 1140 Medium Texture

     

    Swatches Mac Render 1140 Medium Texture

     

     

  • $3.50

    BS Blue Cloth Tape 36mm

    Buildsmart Blue Cloth Tape 36mm

    This Cloth tape has been specifically developed for the rendering industry. The product provides 7 Day UV protection on aluminium window frames during the rendering process. Adheres to concrete, brick-work, aluminium, PVC and painted surfaces.

    The product is waterproof, clean removes and snaps off loose render when the tape is removed, providing an ultra clean finish.

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Tradies so if you are looking for the right man for your job we can connect you without delay.

     

    This product is part of our large selection of tape’s and you can find more information on this product by following the link below.

     

    Buildsmart Blue Cloth Tape

  • $12.00

    Fischer Adhesive Foam f. Gun 750ml

    Fischer Adhesive Gun foam f. gun PUP 750 750ml

    The fischer hardly flammable gun foam PUP B1 750 has high flame resistance as per building material class B1 of DIN 4102-1. This makes it suitable for the filling and sealing of joints with fire protection requirements. In addition, it is suitable for the highly effective thermal insulation of ETICS façades. The gun foam is also used for fixing and sealing in roofs and walls and for sealing window connection joints. The easy dosability enables controlled filling and insulation as well as saving on costs. The grey fischer PUP B1 750 has a solid valve that offers top security against blockages and the loss of gas. Protective gloves for end users are included.

     

    Advantages

    • The PUFS is hardly flammable in line with the B1 test and can therefore be used between solid, mineral or metal building materials. Thus it provides the highest level of safety.

    • The high-quality solid valve prevents adhesion when being stored horizontally or during long interruptions of work, thus guaranteeing long-lasting functionality.

    • The easy dosage allows for a controlled filling and sealing, and ensures that the correct amount is used.

     

    wettrades.com

    As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable tradesman so if you are looking for the right tradesmen for your job we can connect you without delay.

     

    This product is part of our large selection of our adhesive and sealants range and your can find more information about it on the fischer website.

    Fischer Adhesive foam