Unitex Uni-Trowel 333 Fine Texture 15L

Size: 15L pail

Coverage:

Fine: 9-10 m2

Suitable over: Unitex Specialty Renders

Apply with: Trowel

Safe Use: Refer to the MSDS

As the name implies, this range of Unitex Textured Finishes is designed for trowel application. The products in the Uni-Trowel Décor™ range are applied as a single coat, with the exception of the finer finishes (146 and 333) which due to substrate and or weather conditions, may require an additional wet on wet coat.  Unitex Applied Texture Finishes are acrylic-bound textured coatings designed for decorating interior and exterior walls. Unitex Applied Texture Finishes are suitable for use over surfaces prepared with Render from the Unitex Specialty Renders range. A one coat application offers a long life heavy duty coating. Fine texture coats, i.e. Unitex 146, may require wet on wet two coats. The majority of our Finishes are ready-to-use, water-based products. Unitex Applied Texture Finishes are ideal for commercial and residential exterior walls. Due to the strong binding power of the acrylic, an impact-resistant coating results.  The surface prevents scuffing and is able to withstand hard knocks. Uni-Trowel Décor range are available pre-coloured in 15ltr pails, they contain quality graded fine mineral components and aggregates, together with non-absorbent extenders bound by a well-proven acrylic co-polymer. Coverage rates vary considerably with the surface condition and absorption effect. Typical coverage rates are 6 -10m² per pail. There are several grades of Uni-Trowel Décor.

Biological Resistance
Resistance to attack from bacteria and fungi is provided. This product being a water based acrylic system offers safe handling and low toxicity properties. Dirt, grime and dust on the surface of coatings will act as seed beds for bacterial attack, therefore cleaning and maintenance of your coating is essential to hinder bacterial and fungal attack.

Fire Resistance The full Unitex coating system when subjected to the Early Fire Hazard Tests – Australian Standard AS1530.3:1999 meets the strictest standards.

Water Resistance
The coating, even at exceptionally high build, is formulated with a water vapour permeability factor to allow water vapour from the substrate to leave unhindered and to rainproof the exterior. Rising damp and elevated levels of moisture in the substrate will damage, and possibly delaminate, the surface coating. Please ensure that damp coursing the substrate is in place and prior test moisture content with a moisture meter (maximum 12% WME is allowed) (Builder responsibility).

Colour
The pigmentation is completely integrated during the manufacturing process, which means colour through the entire film thickness. Applied Finishes are available in a practically unlimited range of full colour to pastel shades. Please contact Unitex for the full range of colours available.
Note: Some deep tones cannot be supplied in applied finishes. Contact Unitex for your specific solution. All colours will fade to some degree with time in exterior systems. Do not apply pigmented texture coats over fresh and or not fully cured renders as efflorescent damage (white blotching) may occur. Each pail has a label with the unique code identifying the particular texture type, colour and batch number. This coding ensures that if you require additional product (say to finish off a job), Unitex can match the texture and colour to the original. Note: Conditions on site may change and therefore colour outcome may be different when applied under varying weather conditions.  It is advisable always order 1 or 2 more pails than are required for the job. The pails have a strong sealed lid to prevent spillage if they should tip over before opening. Even after opening the lid still fits tightly enough when re-sealing to prevent contamination of the remaining product. The product must be protected from heat and cold during transit and storage.

Application Details
A minimum of 72 hours, under ideal temperate conditions, is required for through-dry (and cure) of the render, when the surface is trough dry the Unitex Textured Finish coat may be applied. Dry is measured to be less than 12% WME (Wood Moisture Equivalent) where measured on a Protimeter® Moisture Meter. The substrate must be clean before applying the Finish coat. Any crumbling, loose or damaged substrate render must be removed and the surface patched and made good prior to coating. All surfaces must be free of grease, oils, dirt and dust. Pre-painted surfaces must have flaking paint wire brushed back to a sound substrate. Unitex recommends a base coat of a pigmented Unitex Uni-Substrate Sealer (2 coats) over old renders prior to application of the surface finishes. If multi coats are desired then a minimum of 72 hours between each coat is required. All Unitex Applied Texture Finishes are designed to overcoat Unitex Render from our specialty render range. See Unitex Renders sections for information on suitable base render to use. Application should not be carried out under excessively cold conditions (below 7 °C) or in hot windy conditions (above 32°C).

Site
Unitex strongly advises sign off on all coating systems. Always provide the Builder and Designer with a site texture sample of minimum 2m², finish and colour for written approval nominated the Unitex specified system.

wettrades.com

As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Renderer’s so if you are looking for the right tradesman for your job we can connect you without delay.

This product is part of our large selection of Render materials and you can find more information and data sheets on this product by following the links to the Unitex website.

Unitex 333 Fine Texture

MSDS Unitex 333 Fine Texture

Unitex Uni-Trowel 888 MediumTexture 15L

Size: 15L pail

Coverage:

Fine: 9-10 m2

Suitable over: Unitex Specialty Renders

Apply with: Trowel

Safe Use: Refer to the MSDS

As the name implies, this range of Unitex Textured Finishes is designed for trowel application. The products in the Uni-Trowel Décor™ range are applied as a single coat, with the exception of the finer finishes (146 and 333) which due to substrate and or weather conditions, may require an additional wet on wet coat.  Unitex Applied Texture Finishes are acrylic-bound textured coatings designed for decorating interior and exterior walls. Unitex Applied Texture Finishes are suitable for use over surfaces prepared with Render from the Unitex Specialty Renders range. A one coat application offers a long life heavy duty coating. Fine texture coats, i.e. Unitex 146, may require wet on wet two coats. The majority of our Finishes are ready-to-use, water-based products. Unitex Applied Texture Finishes are ideal for commercial and residential exterior walls. Due to the strong binding power of the acrylic, an impact-resistant coating results.  The surface prevents scuffing and is able to withstand hard knocks. Uni-Trowel Décor range are available pre-coloured in 15ltr pails, they contain quality graded fine mineral components and aggregates, together with non-absorbent extenders bound by a well-proven acrylic co-polymer. Coverage rates vary considerably with the surface condition and absorption effect. Typical coverage rates are 6 -10m² per pail. There are several grades of Uni-Trowel Décor.

Biological Resistance
Resistance to attack from bacteria and fungi is provided. This product being a water based acrylic system offers safe handling and low toxicity properties. Dirt, grime and dust on the surface of coatings will act as seed beds for bacterial attack, therefore cleaning and maintenance of your coating is essential to hinder bacterial and fungal attack.

Fire Resistance The full Unitex coating system when subjected to the Early Fire Hazard Tests – Australian Standard AS1530.3:1999 meets the strictest standards.

Water Resistance
The coating, even at exceptionally high build, is formulated with a water vapour permeability factor to allow water vapour from the substrate to leave unhindered and to rainproof the exterior. Rising damp and elevated levels of moisture in the substrate will damage, and possibly delaminate, the surface coating. Please ensure that damp coursing the substrate is in place and prior test moisture content with a moisture meter (maximum 12% WME is allowed) (Builder responsibility).

Colour
The pigmentation is completely integrated during the manufacturing process, which means colour through the entire film thickness. Applied Finishes are available in a practically unlimited range of full colour to pastel shades. Please contact Unitex for the full range of colours available.
Note: Some deep tones cannot be supplied in applied finishes. Contact Unitex for your specific solution. All colours will fade to some degree with time in exterior systems. Do not apply pigmented texture coats over fresh and or not fully cured renders as efflorescent damage (white blotching) may occur. Each pail has a label with the unique code identifying the particular texture type, colour and batch number. This coding ensures that if you require additional product (say to finish off a job), Unitex can match the texture and colour to the original. Note: Conditions on site may change and therefore colour outcome may be different when applied under varying weather conditions.  It is advisable always order 1 or 2 more pails than are required for the job. The pails have a strong sealed lid to prevent spillage if they should tip over before opening. Even after opening the lid still fits tightly enough when re-sealing to prevent contamination of the remaining product. The product must be protected from heat and cold during transit and storage.

Application Details
A minimum of 72 hours, under ideal temperate conditions, is required for through-dry (and cure) of the render, when the surface is trough dry the Unitex Textured Finish coat may be applied. Dry is measured to be less than 12% WME (Wood Moisture Equivalent) where measured on a Protimeter® Moisture Meter. The substrate must be clean before applying the Finish coat. Any crumbling, loose or damaged substrate render must be removed and the surface patched and made good prior to coating. All surfaces must be free of grease, oils, dirt and dust. Pre-painted surfaces must have flaking paint wire brushed back to a sound substrate. Unitex recommends a base coat of a pigmented Unitex Uni-Substrate Sealer (2 coats) over old renders prior to application of the surface finishes. If multi coats are desired then a minimum of 72 hours between each coat is required. All Unitex Applied Texture Finishes are designed to overcoat Unitex Render from our specialty render range. See Unitex Renders sections for information on suitable base render to use. Application should not be carried out under excessively cold conditions (below 7 °C) or in hot windy conditions (above 32°C).

Site
Unitex strongly advises sign off on all coating systems. Always provide the Builder and Designer with a site texture sample of minimum 2m², finish and colour for written approval nominated the Unitex specified system.

wettrades.com

As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Renderer’s so if you are looking for the right tradesman for your job we can connect you without delay.

This product is part of our large selection of Render materials and you can find more information and data sheets on this product by following the links to the Unitex website. 

Unitex 888 Medium Texture

Unitex Uni-Dry Cote Powder Texture 20Kg

Trowel applied dry powder finish coats which require the mixing of water on site. Uni-Cote Textures provide the textured effect with the Uni-PTC top coat, or Uni-Flex membrane, to provide the colour. The Uni-Cote Dry Powder Texture range separate texture from colour and therefore is ideal in weather/temperature conditions where it may be difficult to achieve rapid, through drying of an acrylic based texture coat. This product must be over-coated with Unitex Uni-PTC for decorative colour effect.

Unitex 846 fine sand texture

Unitex855 medium texture

Size: 20kg bags

Coverage: 8-12m²

Suitable over: Unitex Speciality Renders

Overcoated with: Uni-PTC (Protective Top Coat)

Apply with: Trowel

Zero emission product

Safe Use: Refer to the MSDS

Add water, Mix & Apply

Unitex Uni-Dry Cote® unique powder finishes are dry powder-based products. They are a cement modified, polymer-based blend of fine marble, quality-graded mineral and polymeric additives to provide a 100% active product. On-site, all that has to be added is water to provide a ready-to-apply finish.

Unitex Applied Texture Finishes are polymer/mineral bound textured coatings designed for decorating interior and exterior walls. Unitex Applied Texture Finishes are suitable for use over surfaces prepared with render from the Unitex Specialty Renders range. A one coat application offers a long-life, heavy-duty coating.

Unitex Applied Texture Finishes are ideal for commercial and residential exterior walls. Due to the strong binding power of the acrylic, an impact resistant coating results.  The surface prevents scuffing and is able to withstand hard knocks.

Unitex Uni-Dry Cote® Powder Finishes are supplied in 20kg multi-walled paper sacks. They contain quality graded fine mineral components and aggregates, together with non-absorbent extenders bound by a well-proven polymer system. Typical coverage is 8-12m² per bag.

There are four grades of Unitex Uni-Dry Cote®.  

In order, from coarsest to finest, they are;

Unitex 855 – Medium Towel Finish

Unitex 846 – Fine Trowel Finish

Uni-Cote Dry Powder Finishes:

Biological Resistance 

Resistance to attack from bacteria and fungi is provided. This product being a cement modified water based polymer system offers safe handling and low toxicity properties. Dirt, grime and dust on the surface of coatings will act as seed beds for bacterial attack, therefore cleaning and maintenance of your coating is essential to hinder bacterial and fungal attack.

Fire Resistance

The full Unitex coating system when subjected to the Early Fire Hazard Tests – Australian Standard AS1530.3:1999 meets the strictest standards.

Water Resistance

The coating, even at exceptionally high build, is formulated with a water vapour permeability factor to rainproof the exterior and allow water vapour from the substrate to leave unhindered. Rising damp and elevated levels of moisture in the substrate will damage, and possibly delaminate, the surface coating. Please ensure that damp coursing the substrate is in place and prior test moisture content with a moisture meter (maximum 12% WME is allowed) (Builder responsibility).

Colour

The Unitex Uni-Dry Cote® Powder Finishes are not pigmented products. They dry on the surface to a ‘cement-off-white’ colour. The desired topcoat colour is achieved by application of a pigmented protective membrane such as Unitex Uni-PTC for a matt surface effect or Unitex Uni-Flex Membrane for a satin surface finish. 

Application Details
A minimum of 72 hours, under ideal temperate conditions, is required for through-dry (and cure) of the render, when the surface is through dry the Unitex Textured Finish coat may be applied. Dry is measured to be less than 12% WME (Wood Moisture Equivalent) where measured on a Protimeter® Moisture Meter.

The substrate must be clean before applying the Finish coat. Any crumbling, loose or damaged substrate render must be removed and the surface patched and made good prior to coating. All surfaces must be free of grease, oils, dirt and dust. Pre-painted surfaces must have flaking paint wire brushed back to a sound substrate. Unitex recommends a base coat of a pigmented Unitex Uni-Substrate Sealer (2 coats) over renders prior to application of the surface finishes.

If multi coats are desired then a minimum of 72 hours between each coat is required.

All Unitex Applied Texture Finishes are designed to overcoat Unitex Render from our specialty render range. See Unitex Renders sections for information on suitable base render to use. Unitex Uni-Dry Cote® Powders, when through dry and cured, are to be over coated with two coats of a Unitex Uni-PTC Protective Membrane. 

Application should not be carried out under excessively cold conditions (below 7 °C) or in hot windy conditions (above 32°C).

Guide to Good Mixing Consistency

1. Add the contents of the bag slowly to 4 litres of water (25% volume of entire bag) with vigorous drill mixing to ensure a lump free render of required slump.  Allow to stand for 5-10 minutes and re-whip with mixer to allow efficient wetting and ideal application consistency.

2. The mix can be later water thinned to required viscosity within 1 hour of initial mixing.

3. Ensure wall surface is stable, clean, dry and free of dust, etc prior to application.

Site

Unitex strongly advises sign off on all coating systems. Always provide the Builder and Designer with a site texture sample of minimum 2m², finish and colour for written approval nominated the Unitex specified system.

wettrades.com

As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Renderer’s so if you are looking for the right tradesman for your job we can connect you without delay.

This product is part of our large selection of Render materials and you can find more information and data sheets on this product by following the links to the Unitex website.

Unitex Dry Texture

Unitex Uni-Dry Cote HiLite Render 14Kg

Suitable for all high and very high-build applications over uneven surfaces. Can be applied over many substrates including Brickwork, Concrete slabs and Panels. It is ideal for multi-substrate application. Is able to achieve 30mm depth in 2-3 passes. A lightweight render, not adding excessive weight to the structure. Easy to use for all skill levels.

Size: 14kg bags

Coverage: 2-4m2

Suitable for: New Bricks, Old Bricks, Cement Block

Apply with: Spray or Trowel

Safe Use: Refer to the MSDS 

Uni-Dry Cote® HiLite Render™ is a trowel-applied or spray machine applied high build, light weight render, suitable for a one-coat or two-coat application on all suitable Brick or Block etc, masonry surfaces both inside and out, and is recommended to aid in the protection of masonry walls from the damaging effect of surface ingress of moisture. Due to its light weight, high build can be achieved, even over difficult / uneven masonry surfaces.

Uni-Dry Cote® HiLite Render™ is a cement-based polymer modified, High Performance, Water Resistant and Adhesion Promotion masonry render system. Uni-Dry Cote® HiLite Render™ is applied direct to sound and prepared masonry surfaces, either mechanically (sprayed) or by Trowel and rubbed up to a true and even surface. This product is workable at thicknesses from 6 mm up to approximately 15 mm. 30 mm may be achieved with successive coats of 15 mm build up. A minimum curing time of 24 hours between coats is required.

Uni-Dry Cote® HiLite Render™ is ideal for building up rough brickwork or filling of rake joins where a skim coat is not suitable.

Uni-Dry Cote® HiLite Render™ is supplied in ready-to-use 14kg bags.

Condition of Substrate

Before application of any render the surface of the substrate must be clean, dry and free of any debris. This means that any loose or damaged substrate must be removed, or patched and made good, prior to application of the base render.

The dry substrate surface must be cleaned free of any grease, oils, scaling laitance, efflorescence, form-oil compounds, mould, fungi, rust, dirt, dust or any other foreign matter. Pre-painted surfaces must be wire-brushed back to the bare substrate.

It is the responsibility of the Builder or Head Contractor to make good any substrate before the render is applied.

Adequate expansion joints are required to minimise cracking on the surface of the render. Location of the expansion joints is also the responsibility of the Builder or Head Contractor. Unitex® recommends expansion joints to every elevation and between different substrates, to allow for building movements and or stresses. Ideally, expansion joints should be at all penetrations to wall surface.

If such expansion joints are not provided by the Builder or Head Contractor, cracking due to movement of the substrate may occur. This is in no way indicative of faulty material. Rather it indicates sub-standard building practice.

Adding Water

Uni-Dry Cote® HiLite Render™ products are dry powder-based products. This means that you are getting a 100% active product. All that is required is for clean water to be mixed in, on site, immediately prior to application to the substrate.

The recommended starting point is to add approx. 25% by volume, (based on the amount of powder render to be used), of water into a clean container (approx 4.5 litres per bag). Then slowly add the powder, with drill mixing, until the desired slump (consistency) is achieved.

Uni-Dry Cote® HiLite Render™ should be left a minimum 24 hours after drying before overcoating with a texture from the Unitex Applied Finishes range.

Uni-Dry Cote® HiLite Render™:

• Ideal for uneven masonry surfaces

• Trowels on easily, smoothly and thickly

• High build in a single pass

• Is polymer-modified for strong adhesion to surface

• Is more waterproof than conventional render

• Just Add Water  – less margin for errors

• Is ideal for renovation works or over new surfaces

• Consistent quality

Guide to Good Mixing Consistency

1. Add the contents of the bag slowly to 4 litres of water (25% volume of entire bag) with vigorous drill mixing to ensure a lump free render of required slump.

2. The mix can be later water thinned to required viscosity.

3. Ensure wall surface is stable, clean, dry and free of dust, etc prior to application.

4. For difficult masonry and non-masonry surfaces contact Unitex for product and surface preparation advice.

wettrades.com

As a small streamlined business we are able to deliver to quality products at a great price. Although we deliver Australia wide our business offers super quick and reliable service to Melbourne and especially the Bayside area as we are located in Highett. We also deal with a large range of reliable Renderer’s so if you are looking for the right tradesman for your job we can connect you without delay.

This product is part of our large selection of Render materials and you can find more information and data sheets on this product by following the links to the Unitex website. 

Unitex Hi Lite Render

MSDS Unitex Hi Lite Render